Present the Can and End
Send matching can and lid samples. Agree who positions each part, how the can is supported and what confirms readiness before a cycle starts.
Semi Auto Vacuum And Gas Nitrogen Flushing Round Can Sealing Machine
A Semi-Automatic Round Can Seaming Configuration
Review operator handling, the can and end, and the proposed vacuum and nitrogen cycle together. This semi-automatic equipment family needs its own loading and unloading plan before it can be fitted into a packaging operation.
Discuss Your Can and EndDownload reference notes (TXT)
This reference TXT is not a formal specification PDF.
Reference Specifications
Levapack reference description only. The listed materials and model are not confirmed specifications of a Deepack offer.
| Item | Reference description |
|---|---|
| Reference model | LPE-SVC05 |
| Rollers and chuck — source description | Cr12 die steel |
| Cover and main parts — source description | SUS304 stainless steel |
| Vacuum-system seal — source description | Silica gel, as described by the source; exact material grade requires confirmation |
| Output and container dimensions | Not stated in the reviewed page description |
| Vacuum and gas performance | No confirmed vacuum level, residual oxygen value or gas consumption |
| Offered Deepack configuration | Model, materials, tooling and utilities to be confirmed |
Read the source and confirmation limits
The source description lists the model and three material statements. It does not establish a tested vacuum level, oxygen result, shelf life, throughput or a complete operating sequence.
Plan the Operator Handling Steps
Review the Cycle
Ask the supplier to demonstrate the proposed evacuation, gas admission and seaming sequence. Confirm controls, interlocks and recovery after interruption on the offered machine.
Remove and Inspect
Agree safe release and unloading steps, where the finished can is placed and how seam checks are recorded during a run.
These are planning checks, not a verified instruction manual. The exact loading method and cycle need supplier confirmation.
Match the Package, Tooling and Utilities
Can body and end compatibility
Provide body material, diameter, height, flange and end drawings. Review the chuck, support plate and roller profiles for every intended format using actual samples.
Vacuum and nitrogen equipment scope
Request the pump specification, gas supply conditions, connection layout and included components. Agree measured acceptance criteria and the test method; the machine name alone does not establish performance.
Operator access and changeover
Review loading reach, guarding, cleaning access and format changes. Request the list of change parts and a demonstrated procedure before finalizing the workstation layout.
Compare Handling with the Fully Automatic Model
This reference is the semi-automatic LPE-SVC05. The existing fully automatic nitrogen filling and vacuum sealing detail belongs to a separate equipment route. Confirm can infeed, end placement, cycle initiation and discharge individually when comparing proposals; automatic-model speed or process statements do not transfer to this model.
View the fully automatic nitrogen filling and vacuum sealing model
Agree What the Sample Trial Must Show
- Check the matched can and end against the proposed tooling.
- Document the operator steps and demonstrated machine sequence.
- Record seam inspection results using agreed sampling and acceptance criteria.
- If gas or vacuum performance is required, define instruments, sampling point, timing and test conditions separately.
- Confirm actual output with the complete handling cycle and planned package.
A successful seam does not by itself establish residual oxygen, vacuum retention or shelf life. Any preservation requirement needs evidence for the product and complete package under defined conditions.
Prepare Your Equipment Brief
- Matching can and end samples with dimensioned drawings
- Product, fill quantity and headspace requirements
- Required output and operator handling arrangement
- Available electrical and gas supplies and workstation dimensions
- Seam inspection criteria and any separate gas or vacuum test requirements
- Requested material records, manual, tooling list and service scope
Confirm certification and commercial commitments against the offered equipment documents.
Review Your Sample TrialSemi-Automatic Can Seaming FAQs
Is this the fully automatic nitrogen filling model?
No. LPE-SVC05 identifies this source semi-automatic model. The fully automatic model has a separate detail page and needs a separate handling and specification review.
Does semi-automatic define every operator step?
No. Confirm can loading, end placement, starting, release and unloading with the supplier demonstration and manual.
Are the listed materials confirmed for Deepack?
No. They describe the reference model. Ask for material specifications and supporting records for the offered equipment.
Is a residual oxygen value guaranteed?
No oxygen result or preservation guarantee is established here. Agree a relevant measurement method and acceptance criteria if needed.
Can one tooling set seal every can size?
Compatibility and change parts depend on the can and end geometry. Submit each format for tooling review and sample trials.
What happens after I submit an enquiry?
The form validates your entries and states that they have not been sent. Live delivery and a formal specification PDF remain pending.
Return to the Equipment Categories
Discuss Your Semi-Automatic Can Seaming Project
Tell us your can and end dimensions, product, handling plan and required output.